Page 35
( Displaying 10 of 643 Products )
|
|
Townshend Seismic Podiums
|
|
Seismic Isolation Podium
Designed as a range to accommodate any size and weight of speaker – standmount plus stand, floorstander or subwoofer – the Seismic Podium breaks the acoustic connection between the floor and the speaker, preventing the passage of deleterious vibrations both to and from the speaker cabinets. For a detailed explanation of why this is an absolute necessity before any speaker can perform to its true potential, read ‘Earthquakes on hi-fi’.
|
Townshend Seismic Platform
|
|
Seismic Vibration Isolation Platform
Ultra thin platform disappears under equipment
Enhances clarity across the frequency range
Delivers wider and deeper soundstages
Improves bass definition
Reduced muddiness and smear
Makes transients clearer
Especially designed to isolate individual components such as CD players, turntables, DACs, preamplifiers, power amplifiers and streamers from vibration.
The Seismic Isolation Platform includes a durable slim steel top plate that integrates unobtrusively under any hi-fi component. The acoustically dead constrained-layer damped plate combined with a Seismic Load Cell™ attached to each corner is the ultimate combination to absorb and isolate unwanted vibration, including structural, air-borne and that generated by the hi-fi equipment.
|
Linn (MECH 072/2) No.6 X 3/4 POZI RND Woodscrew Black Zinc
|
|
Linn self tapping black zinc 3/4" woodscrews.
These 3/4" length wood screws are used in the following places on the Linn LP12 Turntable:
4x used to attach the 4 rubber feet through the baseboard and into the base of the wooden plinth.
2x used on the baseboard to secure the middle rectangular washers.
2x used for the plastic Mains cable clamp on exiting the wooden plinth.
2x used for the mains cable clamp found on the wiring strap.
|
Linn (Mech 016) No.6 X 1/2 Supa Pan Self Tapping Screw
|
|
Linn 1/2" length Wood screw used in the following places on the Linn LP12 turntable:
8x used to secure the hinge back plates to the rear of the LP12 wooden plinth.
8x used for Solid Base and Trampolin base board.
4x used to secure wiring strap to wooden plinth.
|
Avid SIEVEKING Shielding RCA and XLR Covers
|
|
Sieveking Sound
Avid is pleased to confirm distribution of Sieveking Sound from Germany.
Sieveking Sound RCA and XLR End Caps are a NECCESARY accessory for all unused analogue inputs and outputs of audio components.
The caps are made of pure copper and are coated with gold. Inside there is an additional Teflon insert. This unique combination allows excellent high-frequency absorption.
|
Avid Isopuks
|
|
Isopuks are highly effective isolators designed to reduce structure borne vibration and its deleterious effects on audio signals.
Structure borne vibration affects virtually every piece of audio equipment, but its effects are most damaging to the tiny signals read and processed by source components such as CD players and non-isolated turntables.
Vibration enters audio components via the feet & the chassis, reducing clarity, smearing detail and distorting frequency response. Eliminating this structural resonance in audio equipment results in instantaneous audible improvements; increases in soundstaging, improved imaging and (most importantly) smoother more natural tonal balance.
|
Artesania Audio High Mass Dampers
|
|
Dampers are anti-magnetic and shock absorbing
masses that act against vibrations generated in
electronic components. These could be from
power sources (transformers) and could also be a
consequence of the ondulatory movement of
sound as it bounces back off the furniture and
cabinets housing electronic equipment. These
air-borne vibrations cause interference and
background noise that are detrimental to the
listening experience.
|
|
|
|
|
|
|
|
|
|
|
£ 149.00
* |
|
|
|
|
|
£ 188.00
* |
|
|
|
|
|
£ 248.00
* |
|
|
* Only available for purchase in-store |
Palladio Transformer (PAL-TRA)
|
|
Palladio Transformer (PAL-TRA) - Replacement Part
Palladio's Transformer Unit is compatible with all Palladio Home Cinema Seating.
|
Michell Cartridge Tags (set of 4)
|
|
These are the ultimate cartridge tags and they come as standard on Michell's Techno Arm ‘A’. Silver-platted for superior conductivity, their cartridge tags are milled from solid brass and offer a unique spring-loaded connection for improved pin contact. Four colour-coded heat-shrink sleeves are included.
|
Michell New Rega 3-Point VTA Adjuster
|
|
New Rega 3-Point VTA Adjuster
The Rega 3-point fixing VTA (Vertical Tracking Angle) Arm Adjuster has been designed for the range of Rega arms (RB-251 and RB301) that use the recently introduced 3-point fixing. Once installed, the user can adjust the vertical tracking angle in minute increments without losing the rigid 3-point mounting so important to proper sound reproduction.
The VTA adjustor, at its minimum setting, raises the tone arm by 2mm, which is the same as the thinnest setting on the moulded adjuster available from Rega. It comes packed with two different thickness adjuster rings (the thinner ring is designed to lift the tonearm base 0 to 2mm and the thicker ring will lift the base 2 to 4 mm) and all of the fixings necessary as well as a nylon nib to help rotate the base notches if access is tight.
|
Page 35
( Displaying 10 of 643 Products )
|
|
Search for products that may contain the words:
within
using