|
Page 2
( Displaying 10 of 359 Products )
|
|
|
Furman M-10XE (M10XE) Power Conditioner 10A 230V
|
|
M-10X E - 10A Standard Power Conditioner, 230V
Furman M-10X E
Install an M-10x E in to the top slot of your rack, and the ten switched outlets in the rear panel will power up and protect all your equipment up to a 10-amp load.
A Merit Series Power Conditioner is the perfect low-cost AC power solution for any rack mount system.
Applications:-
INSTRUMENT RIGS
You've got a rack for your effects, preamps, tuner...You're going to plug that into the wall? One big spike and your rig is up in smoke. Furman's standard level surge/spike protection defends your gear from the spikes and surges that are so common at gigs and practice spots. With Furman's standard level RFI/EMI filtration, you'll get a quieter tone without pops, crackles, and the local radio station coming out of your amp. Plus, dual pull-out lamps (M-10Lx E) let you see your rack without turning the house lights on.
|
|
WyreStorm CON-H2-EDID (CONH2EDID) HDMI In-line signal Re-Clocker
|
|
CON-H2-EDID
HDMI In-line Signal Re-Clocker with EDID Management, Automatic or Manual CEC, Audio De-embed and Relay Triggering
A multi-purpose installer tool, the CON-H2-EDID can perform a variety of tasks within an install. As an in-line device it can act as an EDID manager to request specific content from a source or as an audio de-embedder, extracting HDMI source audio via the S/PDIF or stereo mini-jack ports. Additionally it can be a micro zone controller, sending CEC and RS-232 power triggers to connected projectors or screens and from its two relay ports, can trigger devices in the zone using signal presence logic.
|
|
WyreStorm CON-H2-SCL (CONH2SCL) In-Line HDMI Down-Scaler
|
|
CON-H2-SCL - 4K 4:4:4 60Hz In-Line HDMI Scaler with Audio Breakout
An essential tool when mixing 4K & 2K screens on the same distribution system, the CON-H2-SCL enables in-line scaling of HDMI content. An HDMI signal from a source device, DA or matrix is converted so that it can be accepted by the connected display. Via a powerful scaling chip, 4K/60 4:4:4 or 4:2:0 can be down-scaled to as low as 480P; likewise, content can be up-scaled to 4K/60 4:4:4. Set up & configuration is done using a simple PC tool which is part of WyreStorm Management Suite V1.6. The software tool allows management of the scaling function and EDID via a simple interface.
|
|
WyreStorm NHD-RACK4 Mounting Brackets for NHD-000-RACK4
|
|
NHD-RACK4-BRA - Accessory for the NHD-000-RACK4 6U/12 Slot Rack Mount
The NHD-000-RACK4 includes 7 blanking plates but does not include the NetworkHD/Enado Mini device mounting brackets - these are included with the device to be mounted.
These spare brackets or additional blanking plates are available separately. Please ensure the correct part number is selected for the device to be mounted.
The
|
|
WyreStorm NHD-140-RACK-1U (NHD140RACK1U)
|
|
NHD-140-RACK-1U - 1U/2 Slot Rack Mount for NetworkHD™ NHD-140-TX
The NHD-140-RACK-1U is a 1U rack mount that provides a clean installation for up to 2 NetworkHD™ 100 Series NHD-140-TX quad encoders. The minimal rack unit height and compact mounting arrangement allows a very high NetworkHD™ 100 Series encoder density designed for space restricted deployments.
The robust and thermally optimised design helps keep your centralized NetworkHD solution perfectly organized.
|
|
CYP SY-300H-4K22 (SY300H4K22) HDMI to HDMI Scaler
|
|
SY-300H-4K22 HDMI to HDMI Scaler with Audio Embedding & De-Embedding
This SY-300H-4K22 accepts and outputs a wide range of resolutions up to 4K @ 60Hz (4:4:4, 8-bit) with simultaneous audio embedding and de-embedding of digital (HDMI or optical) or analogue audio. Integrated EDID and HDCP management allow for control over the connected sources and displays detected by the unit. The scaled HDMI output is powered by a high quality single-pass scaling engine with the ability to adjust the image with a number of fine tuning options including: contrast, brightness, hue, saturation, sharpness, noise reduction, and RGB levels. 3-D motion adaptive de-interlacing and frame rate conversion is supported as well.
|
|
CYP EL-42PIP (EL42PIP) 4 x 2 HDMI Switch with Integrated Multi-View
|
|
EL-42PIP 4 x 2 HDMI Switch with Integrated Multi-View (Picture In Picture) Technology
The EL-42PIP is a High Performance HDMI switch with integrated scaling and multi-view (PIP) technology. This unit id the ideal solution for monitoring or displaying multiple sources simultaneously, making it highly suited for corporate, commercial or classroom environments.
Any one of the four HDMI sources can be displayed individually in full screen mode, or displayed in a umber of pre-configured formats in the PIP mode. Management of the input sources routing, position and sizing can be controlled easily using the OSD, WebGui or front panel controls. The input sources can then be outputted via the units two mirrored HDMI outputs. The unit also acts as a seamless switcher providing additional confidence in demanding corporate environments.
|
|
CYP PUV-1830RX-AVLC (PUV1830RXAVLC) Receiver
|
|
PUV-1830RX-AVLC 100m HDBaseT™ HDR Receiver (4K, HDCP2.2, PoH, LAN, OAR, 18Gbps)
The new PUV-1830RX-AVLC Receiver enables video resolutions up to 4K UHD including 10/12-bit HDR & Dolby Vision, to be received along with HD audio, 2-Way IR, RS-232, PoH (Power over HDBaseT) and LAN signals from a distance of 100m. This solution provides advanced signal management ensuring reliable results in the most demanding installation environments. All audio, video, control, and power are received simultaneously over a single CAT6a/7 cable up to 70m. Using the OAR (Optical Audio Return) feature, audio can be sent from the display or local source back to the TX.
|
|
CYP PUV-1830TX-AVLC (PUV1830TXAVLC) Transmitter
|
|
PUV-1830TX-AVLC 100m HDBaseT™ HDR Transmitter (4K, HDCP2.2, PoH, LAN, OAR, 18Gbps)
The new PUV-1830TX-AVLC Transmitter enables video resolutions up to 4K UHD including 10/12-bit HDR & Dolby Vision, to be transmitted along with HD audio, 2-Way IR, RS-232, PoH (Power over HDBaseT) and LAN signals up to a distance of 100m. This solution provides advanced signal management ensuring reliable results in the most demanding installation environments. All audio, video, control, and power are transmitted simultaneously over a single CAT6a/7 cable up to 70m. This unit also features OAR (Optical Audio Return) allowing the user to extract Optical Audio transmitted from the HDBaseT Receiver.
|
|
CYP PUV-1820TX-AVLC (PUV1820TXAVLC) 5-Play HDBaseT™ Transmitter
|
|
PUV-1820TX-AVLC 100m HDBaseT™ 4KHDR Transmitter + 1 x HDMI Input, 1 x HDMI Output, 1 x HDBaseT Output (4K, HDCP2.2, PoH, LAN, 18Gbps, AVLC)
The new PUV-1820TX-AVLC Transmitter enables video resolutions up to 4K UHD including 10/12-bit HDR & Dolby Vision, to be transmitted along with HD audio, 2-Way IR, RS-232, PoH (Power over HDBaseT) and LAN signals up to a distance of 100m. This solution provides advanced signal management ensuring reliable results in the most demanding installation environments. All audio, video, control, and power are transmitted simultaneously over a single CAT6a/7 cable up to 70m.
|
|
Page 2
( Displaying 10 of 359 Products )
|
|
Search for products that may contain the words:
within
using